$25 off all services · online only · mention this ad ·

.png)


BOAT DOCK ELECTRICAL WORK ON NORTHEAST TEXAS LAKES
Power, lighting and shore power on private docks around Lake Tawakoni and Lake Ray Hubbard. Every job runs under Kyle Robison, our master electrician of record, license #782768.
Boat dock electrical work covers the feeder from the house panel out to the dock, a disconnect on shore, ground-fault protection on every dock circuit, and the outlets, lighting and shore power on the structure itself. On a private dock the lake’s owner approves the plan before construction starts, and the city permits the work.



ANATOMY OF A DOCK CIRCUIT
TAP A PIECE OF THE DOCK TO SEE WHAT IT DOES
A dock circuit is not an outdoor outlet on a longer run. It is a small system that starts at the house and ends over open water, and every piece of it has a job.

.png)
DOCK POWER AND CIRCUITS
The feeder from the house panel, the disconnect on shore, and the branch circuits out on the structure. Ground-fault protection on every circuit that reaches the water.
DOCK ELECTRICAL, START TO FINISH
Everything on a dock traces back to one circuit leaving the house. We work on that circuit and everything hanging off it.

WHAT THE WORK COVERS
FIXED PIERS AND DOCKS
.png)
We work on fixed structures. We do not take floating docks.
.png)
SHORE POWER PEDESTALS
We install them and we repair them. The pedestal, the breaker feeding it, and the wiring behind it, sized to what the boat actually draws rather than to what fits.
.png)
DOCK, PIER AND UNDERWATER LIGHTING
Catwalk and post lighting, and underwater fixtures too. Everything rated for where it actually sits, and aimed the way the lake authority wants it aimed.
.png)
REPAIRS TO EXISTING DOCK WIRING
Corroded connections, dead circuits, a ground-fault device that trips the moment it is reset, fixtures that failed a season after they went in.
.png)
STRAY CURRENT TESTING
We test for and troubleshoot current that is leaving a circuit and reaching the water. It is a different job from a normal fault call, and it is the one that matters most before anyone swims.
.png)
BOAT LIFT WIRING
Motor connection, disconnect, and stop and start controls. The lift itself is set by a marine contractor. We do not install lifts. We wire them.
PRIVATE DOCKS
.png)
Residential. Not marinas or multi-slip commercial docks.
WE CAN FILE THE PERMITS
.png)
With the lake authority and with the city. You are a party to it too.

WHAT A LAKE DOES TO A CIRCUIT
.png)
THE PART NOBODY SEES


The fault runs to earth and the breaker trips
BACK YARD
There is no earth, so the water takes it
DOCK
01. THE WATER IS A PATH
A fault finds earth and the breaker trips. The story ends there.
This is the difference that matters most, and it is the reason ground-fault protection out there is not a convenience feature. A swimmer in energized water can lose the ability to swim before reaching the ladder.
02. THE WATER LINE DOES NOT STAY PUT
The ground stays where you left it.
A pier does not move, but the lake does, and the fittings that were fine dry are the ones that fail wet. It is also why the takeline rules on Lake Ray Hubbard are written around elevations rather than around distances.
03. EVERYTHING OUT THERE IS CORRODING
Shaded part of the day, dry most of the year, and sheltered by the house.
The wrong cable jacket, the wrong fitting or the wrong pairing of metals fails early out here, and it does it quietly. Choosing for the environment is most of the job.
04. IT IS THE CIRCUIT NOBODY LOOKS AT
You use those outlets all year, so you notice the day one stops working.
A dock circuit can sit wrong for years without anybody knowing, because nothing about it is in front of you day to day. That is the case for having it looked at rather than waiting for it to announce itself.
There is no earth to find. The current spreads through the water instead, and that is the water people swim in.
The lake rises and falls. A fitting sitting well clear of the water in one season can be sitting in it the next.
Wet, in full sun, and carrying whatever runs off the lawn upstream.
Seasonal, out of sight, and often put in by whoever built the dock rather than by an electrician.
A back yard forgives a lot. Put the same circuit over open water and four things change, and every one of them changes how it gets built.
CURRENT ALREADY IN THE WATER IS ITS OWN JOB
Finding leakage that is reaching the water is not the same call as chasing a dead outlet, and it is not something you can check from the deck. We test for it and we troubleshoot it. If anything about your dock circuit has you unsure, that is the call to make before the season starts.



Whoever owns the lake makes the rules
Three lakes, three rulebooks
A dock is not like a shed in the back yard. The land under it usually belongs to somebody else, and that somebody has to approve the plan before anyone starts. Which body that is depends entirely on which water you are on.

.png)
WE PREPARE AND FILE
With the lake authority and with the city. You sign the parts only an owner can sign, because the lease on the water side is in your name.
A dock job needs a yes from whoever owns the water and a permit from the city, and they do not run at the same time. Which bodies those are depends on your lake and your address, and that is our problem rather than yours.
TWO APPROVALS, AND WE HANDLE THEM

BEFORE ANYBODY STARTS

WE CHECK THE CODE EDITION FIRST
With the lake authority and with the city. You sign the parts only an owner can sign, because the lease on the water side is in your name.

THEN THE WORK STARTS
Not before. On a lakefront, a structure built without the approval can be required to come out, which is the expensive way to learn the order.

WHAT FAILS FIRST ON A DOCK
.png)
TWENTY YEARS OF THE SAME FOUR CALLS
Dock wiring rarely dies all at once. It goes in one of four places, and three of them are visible from the deck if you know what you are looking at.


WHO IS ACTUALLY RESPONSIBLE
ONE NAME, AND YOU CAN CHECK IT YOURSELF
Every job we run, dock or otherwise, runs under Kyle Robison. He is our master electrician of record, and his license number is on this page for a reason: the State of Texas publishes a license register, and you can type that number into it without asking us for anything.
That matters more than usual on a lake. A dock job puts a licensed contractor’s name on a permit application to a body that owns the water, and it is fair to want to know whose name that is before the application goes in.
Kyle is the master of record and he leads the work. Every job runs under his license, his leadership and his standard.
What comes with the work
.png)
Three year warranty
Our labor and parts warranty runs three years.
.png)
Clean Home Guarantee
Shoe covers at the door, mats down, and your home left cleaner than we found it. A dock circuit starts at your house panel, so a fair bit of a dock job happens indoors.

DOCK WIRING, ANSWERED

QUESTIONS WE GET
Two authorities, and they stack. Whoever owns the water approves the structure and its improvements, and the city with jurisdiction permits and inspects the electrical work. Which bodies those are depends on your lake and your address, and we handle both. A floating structure then adds a third factor, because everything on it has to tolerate constant movement, so the connections and transitions get chosen differently than on a fixed run. Worth saying plainly: we work on fixed piers and docks, and we do not take floating dock work. If yours floats, the approval side above still describes your situation accurately, but you will want a contractor who specialises in floating structures for the build itself.
Not the cable that runs inside your walls. Dock wiring has to survive water, sunlight and movement, so the jacket, the fittings and the metals all get chosen for that. On the copper question specifically, the Army Corps of Engineers’ dock electrical standard for its Beaver Lake project states that branch-circuit wiring there is copper, because the receptacles, devices and light fixtures made for docks are not rated for connection to aluminum conductors. That is the Corps’ standard for its own lake rather than a Texas rule, but the compatibility point behind it holds anywhere those same parts are used. Wire selection for your dock is part of what gets confirmed before a quote goes out.
A dock is normally set up so power to it can be cut from land, without anyone having to step onto the structure to do it. That is the whole point of putting it on shore rather than out on the deck. Practically, it is worth finding out where yours is and making sure a guest could find it in the dark, because the moment you would want it is not the moment to go looking. If you cannot find a disconnect at all, that is worth a call.
Electrically, four things come up over and over. Corroded connections, because every joint sits in damp air. Conduit cracked or pulled apart where the dock flexes. Fixtures and cable that were never rated for a wet, sunlit location and failed a season or two in. And ground-fault devices that either will not reset or have simply never been tested since the day they went in. Three of those four are visible from the deck once you know what you are looking at.
There is no single answer, and anyone giving you one off a weight class alone is guessing. The circuit gets sized to the specific lift you own: its motor, its voltage, and how the manufacturer says it should be fed. Two lifts rated for the same weight can want different circuits. The right sequence is to have the lift’s data in hand first and size the circuit to it, rather than run a circuit and hope the lift fits. We wire lifts, including the motor connection, the disconnect and the stop and start controls, though we do not install the lift itself. Bring us the model and we will work from that.
Test it, and do it before the first warm weekend rather than after. Ground-fault devices carry a test button, and pressing it should cut the power. Then reset it and confirm the power comes back. Two outcomes mean stop: it does not trip when you test it, or it will not reset afterwards. Either way, stop using the dock circuit and get it looked at, because an untested device is an assumption rather than protection. It takes a few seconds and it is the single most useful thing a dock owner can do themselves.

Four of these come straight off what people actually ask Google about dock electrical work. Two we added because they are the ones that come up once somebody is standing on the dock with us.


GET IT LOOKED AT
TELL US WHAT YOUR DOCK IS DOING
Call, text, or send the form. If your dock circuit is tripping, or it will not reset, keep everyone out of the water until it has been looked at.
HANDY TO HAVE WHEN YOU CALL
-
Which lake, and whether the dock is on a sublease or permit already
-
The lift or pedestal model, if the job involves one
-
Whether the dock circuit trips, or has no power at all
Our call-out is $49 in office hours and comes off the work if you go ahead. Outside office hours it is $199, and that one is not credited. We are here Monday to Friday, 7:00am to 5:00pm, and we answer around the clock for emergencies. We quote the job rather than the hour, and you see the options and the price in full before any work starts.


LUCKY SAYS PICK UP THE PHONE.
He is not qualified to give advice, but he is right about this one.

TECL #41101
© 2026 Lucky Electrical LLC. All rights reserved.
Site by





%204.png)