top of page

$25 off all services · online only · mention this ad ·

Group 1597884576 (1).png
Licensed electrician performing an electrical panel replacement and upgrade in a Northeast Texas home.
Sparky the Lucky Electrical mascot promoting electrical panel upgrades and 200 amp service in Northeast Texas.

ELECTRICAL PANEL  REPLACEMENT AND UPGRADE

Every job runs under the license and standard of our master electrician of record, Kyle Robison, TDLR #782768. Serving Northeast Texas since March 2026.

An electrical panel upgrade replaces your existing panel and service equipment with higher-capacity gear, most often moving a home from 100 amps to 200 amps. Most run between $3,500 and $8,500, take 6 to 10 hours on site, and leave your power off for 4 to 8 of them. It is permitted, inspected work, and the utility has to disconnect and reconnect at your meter.

TYPICAL RANGE

$3,500 – $8,500

POWER OFF

4 – 8 HOURS

ON SITE

6 – 10 HOURS

PERMIT

REQUIRED

REQUEST A VISITTEXT US CALL 972-965-9926
Group 1597884448 (4).png
Main Image (22).png

HOW TO TELL YOUR PANEL IS OUT OF CAPACITY

START HERE

Most homeowners do not go looking for a panel upgrade. They run into the ceiling their service was built to, and find out that way.

SIGNS THE PANEL IS THE LIMIT, NOT THE APPLIANCE

Breakers trip when two large loads run at the same time, then reset fine on their own.

Lights dim briefly every time the air conditioner compressor starts.

There is no open slot left in the panel, or the slots are already doubled up.

The service is a fuse box rather than a breaker panel.

A home inspection report has called out the panel.

SIGNS THE PANEL IS THE LIMIT, NOT THE APPLIANCE

There is a burning smell at the panel.

The panel or a breaker is warm to the touch.

A breaker will not reset, or trips again immediately.

Buzzing, crackling, or visible scorching.

That second list is an emergency, not a project. Turn the main off if you can do that safely, and call us. Emergency electrical service.

A home inspection report has called out the panel.

And sometimes nothing is wrong at all. Adding an EV charger, a hot tub, a pool, a shop or a standby generator can put a 100 amp service over its limit on paper before anything is installed.

11 (1).png
Electrical panel diagram showing repair, replacement, and upgrade options for Northeast Texas homes.

UPGRADE, REPLACEMENT OR REPAIR: WHICH ONE YOU ACTUALLY NEED

Three different jobs get called the same thing, and they cost very different amounts. The difference is which parts of the service come out.

THREE DIFFERENT JOBS

REPAIR

Something inside a panel that is otherwise sound and correctly sized: a failed breaker, a loose lug, a corroded neutral. The panel stays.

REPLACEMENT

A panel that has failed or aged out is swapped for a new one at the same amperage, usually because the enclosure has rusted, the bus is damaged, or available breakers no longer fit. The capacity does not change.

UPGRADE

The capacity of the service itself increases. Panel, main breaker, service entrance conductors and often the meter can are replaced together. The utility is involved.

Replaced on a capacity upgrade

A repair touches one component inside the panel. A replacement changes the panel. An upgrade changes the service, which is why the utility has to disconnect at the meter and reconnect after the inspection passes.

​

If the wiring in the house is the older problem, meaning cloth-insulated conductors, knob-and-tube, ungrounded two-wire circuits or aluminum branch circuits, the panel is only half the conversation. The same is true if a home inspector has flagged your panel as one of the older brands: that is an age-and-condition question rather than a capacity one, and it is answered on its own page. If a breaker keeps tripping and the panel is modern and correctly sized, that is a circuit problem, and it belongs with electrical repair.

Replaced or re-established as the job requires

Utility owned

Background Image (12).png

THE JOB, START TO FINISH

A service upgrade is a sequenced job with a utility and a city inspector in the middle of it.

WHAT HAPPENS, AND HOW LONG

A panel upgrade is also the most economical moment to add whole-home surge protection, because the panel is already open. It is not included by default and it is not free, but adding it later means paying for panel access twice.

Main Image (22).png

100, 200 OR 400 AMPS: SIZING THE SERVICE TO THE HOUSE

SIZING

Two hundred amps is the default answer across most of Northeast Texas and it is right most of the time. It is not automatically right for your house.

100 amp electrical service panel for smaller homes and gas appliances in Northeast Texas.

100

Gas heat, gas range, gas water heater

Amp service

Genuinely fine. Nothing here needs upgrading, and we will tell you so.

200 amp electrical service panel upgrade for modern homes with electric appliances in Rockwall County.

200

The same house, after an EV charger goes in

Amp service

One addition, and the calculation no longer fits. This is the most common reason a panel upgrade comes up at all.

400 amp electrical service panel for large homes with EV chargers and electric heating in Hunt County, TX.

400

The same house and the same EV charger

Amp service

The load did not change. The service did. The headroom on the right is what you are actually buying.

If the calculation says 200 and someone quotes you 400, ask what load they added. If it says 200 and someone quotes 100 to bring the price down, that is a decision you will end up paying for twice.

Four hundred amp residential services are sometimes the correct answer, usually with large square footage, a shop or barn on its own subpanel, or well and irrigation loads. We do them.

Where the service runs as a buried lateral rather than an overhead drop, we handle the trenched run ourselves rather than handing you off to another trade.

Main Image (22).png

WHAT A PANEL UPGRADE COSTS

COST

We are not going to put a figure on this page that we cannot stand behind, so here is the range and here is what moves it.

MOST PANEL AND SERVICE UPGRADES

$8,500 – $3,500

We quote the job rather than the hour, and you get options and a price in full before any work starts.

If you have seen a number well under $2,000 online, that number is real, it is just not describing this job in this market. National averages price a panel swapped into the same spot with nothing else touched. A service upgrade replaces more than the panel, it involves the utility, and it is permitted and inspected.

Target amperage. A 100 to 200 amp upgrade is the common one; going to 400 is a different job.

Whether the meter can, service conductors, weatherhead and riser are replaced, or only the panel.

Overhead service versus underground lateral. Underground work involves trenching.

Where the panel is, and whether it is staying there. Relocating one usually adds drywall work.

The condition of the grounding electrode system.

Whether existing circuits need correction before they can be landed on a new panel. This is the one that surprises people, and it is why we look before we quote.

A range is not a quote. It is here so you can tell whether the quote you are holding is in the right neighborhood, ours included.

Group 1597884451 (7) (1).png

WHAT WE COMMIT TO ON EVERY PANEL JOB

Not a sales list. These are the things we will do on your job, and you can hold us to each of them.

WHAT YOU CAN HOLD US TO

BEFORE WE QUOTE

We run the load calculation first, and you can have a copy. We size the service to what the house actually draws, not to a round number.

ON THE DAY

Grounding and bonding get replaced along with the panel. Shoe covers at the door, mats down, and your home left cleaner than we found it.

HOW WE PRICE IT

We quote the job rather than the hour, and you get options and a price in full before any work starts.

Checking which utility serves you is the first thing we do.

If you call us and it turns out to be their line, we will tell you and point you at the right number.

A text confirming your appointment, and another when the electrician is on the way.

Fully licensed and insured. TECL #41101.

Every job runs under the license and standard of our master electrician of record.

Three-year warranty on labor and the materials we supply.

Background (16).png

PANEL UPGRADE QUESTIONS

QUESTIONS
  • Most panel and service upgrades run between $3,500 and $8,500. Where yours lands depends on the target amperage, on whether the service entrance and meter can are being replaced along with the panel, on whether the service is overhead or underground, and on the condition of what we find when the cover comes off. We quote the job rather than the hour, and you get options and a price in full before any work starts.

  • We are typically on site for 6 to 10 hours, and your power is off for 4 to 8 of them. Those two numbers are not the same as how long the whole project takes. The permit goes in first, the utility schedules the disconnect and the reconnect, and the inspection sits between them, so calendar time from first call to finished job is normally longer than the time your lights are out.

  • It can be, and a load calculation is the only way to know rather than a rule of thumb. A modest house on gas heat, a gas range and a gas water heater may sit comfortably inside 100 amps. That same house stops fitting the moment an EV charger, a hot tub, a shop subpanel or an all-electric appliance swap goes in. We run the load calculation first, and you can have a copy, which also means you can take it to anyone else you are getting a quote from.

  • Yes. In most homes the panel and the service equipment are replaced and the existing branch circuits are landed on the new panel, with no rewiring at all. Rewiring only enters the conversation when the branch wiring itself is the problem, which usually means knob-and-tube, cloth-insulated conductors, ungrounded two-wire circuits or aluminum branch circuits. A panel upgrade does not fix those, and it does not hide them either: any circuit that cannot be safely landed on a new panel gets identified during the work.

  • Yes. Panel and service work is permitted, inspected work in the cities we serve. Which code edition applies and which office issues the permit both differ city to city, and inside our footprint three different editions are in force. Before we quote, we confirm which edition your city has adopted and what it requires for your job.

  • In practice, no, and the reasons go beyond licensing. The conductors ahead of the main breaker stay energized after the main is switched off, the utility has to disconnect and reconnect at the meter, and the finished work is inspected. If you are hiring it out, both the individual master electrician and the contracting company are searchable by name on the TDLR public register, and you should check.

Sparky the Lucky Electrical mascot answering FAQs about electrical panel upgrade costs and timelines in Northeast Texas.

Written so the first sentence of each answer stands on its own. If yours is not here, the phone works.

Request an electrical panel upgrade visit form for Northeast Texas residents.
Let us run the numbers

TALK TO THE MASTER ELECTRICIAN BEFORE YOU TALK TO ANYONE ELSE

Tell us what you are trying to add, or what the panel is doing. We will tell you whether it is a capacity problem, a circuit problem or a safety problem, and we will run the load calculation before we quote anything.

CALL 972-965-9926
Sparky the Lucky Electrical mascot ready to help with your electrical panel replacement in Northeast Texas.
TEXT US

Lucky says: have your last power bill handy. It tells us who to call about your meter.

REQUEST A VISIT

Tell us the lake and what the circuit is doing. We will come back to you.

CALLTEXT US

Lucky Electrical LLC · TECL #41101

Footer (1).png

TECL #41101


© 2026 Lucky Electrical LLC. All rights reserved.

Site by

Folder 1 (59) 4.png
bottom of page